{"title":"Interfaces","description":"\u003cp\u003eInterfaces allow a transceiver to be connected to a PC or laptop\u003c\/p\u003e","products":[{"product_id":"cga-sb2000mk2-interface","title":"CGA SB2000MK2 Interface","description":"\u003cp\u003eThe \u003cstrong\u003eCGA SB2000MK2 interface\u003c\/strong\u003e connects your computer to your radio transceiver. Through one interface, you can use CAT\/CI-V rig control, operate digital modes, and control functions like PTT, CW, and FSK. The galvanic isolation between the computer and transceiver helps prevent ground loops and unwanted interference.\u003c\/p\u003e\n\u003cp\u003eThe SB2000MK2 is suitable for radio amateurs who want to use their Yaesu, Icom, or Kenwood transceiver with a computer. With the correct optional interface cable, you can connect various compatible transceivers.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat does the CGA SB2000MK2 do?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe SB2000MK2 brings together the various connections needed for communication between radio software on your computer and your transceiver. Instead of using separate solutions for audio, CAT control, PTT, and CW, these functions run through one central interface.\u003c\/p\u003e\n\u003cp\u003eFor CAT or CI-V control, the interface handles communication between suitable radio software and the transceiver. This allows software, for example, to exchange data about the set frequency and band with the radio.\u003c\/p\u003e\n\u003cp\u003eThe audio connection between the computer's sound card and the transceiver also runs through the SB2000MK2. This allows you to use digital modes such as RTTY, PSK31, SSTV, and FAX. The interface can also be used for CW, FSK, and PTT control, and for recording SSB conversations via the computer.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTwo virtual COM ports via one USB connection\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA significant improvement of the SB2000MK2 compared to the earlier SB2000 is the use of two serial connections. The MK2 uses an FT2232 USB-to-UART solution for this and offers two virtual COM ports via a single USB connection.\u003c\/p\u003e\n\u003cp\u003eThis allows, for example, CAT\/CI-V rig control and other communication or control functions to be used side by side.\u003c\/p\u003e\n\u003cp\u003eThe connection to the computer is made via USB 2.0, eliminating the need for a traditional serial or parallel connection to the computer. The interface also gets its power via USB, so no separate power adapter is required.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eGalvanic isolation between computer and transceiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhen connecting radio equipment and computers, good electrical isolation is important. The CGA SB2000MK2 uses optical isolation for digital signals. The audio connection is separated with a 1:1 audio transformer.\u003c\/p\u003e\n\u003cp\u003eThis galvanic isolation helps reduce ground loops, voltage differences, and unwanted EMC interference between the computer and transceiver. This makes the SB2000MK2 a well-thought-out solution for a permanent shack, but also for portable and mobile radio setups.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCapabilities of the CGA SB2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eCAT and CI-V control of compatible transceivers\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eDigital modes such as RTTY, PSK31, SSTV, and FAX\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eControl of PTT, CW, and FSK via the computer\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eGalvanic isolation with optocouplers and 1:1 audio transformer\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eTwo virtual COM ports and power via a single USB connection\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003eApplications such as EchoLink and recording SSB audio via the computer are also possible, depending on the transceiver and software used.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich transceivers are suitable for the SB2000MK2?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA SB2000MK2 can be used with various transceivers from Yaesu, Icom, and Kenwood, among others. For this, you need an interface cable suitable for your specific transceiver.\u003c\/p\u003e\n\u003cp\u003eVarious optional CGA cable sets are available. The ACC-101, ACC-104, and ACC-105 are intended for various Yaesu models. For Icom, the ACC-102 and ACC-103 are available, among others, and for various Kenwood transceivers, you can use the ACC-106 or ACC-107.\u003c\/p\u003e\n\u003cp\u003eAlways check which cable set belongs to your exact brand and type of transceiver before ordering.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOne interface for computer control and digital radio\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDo you want to use digital modes, control your transceiver from radio software, or control CAT\/CI-V, PTT, and CW via your computer? Then the CGA SB2000MK2 radio interface conveniently brings together the necessary connections.\u003c\/p\u003e\n\u003cp\u003eThanks to its USB connection, two virtual COM ports, and galvanic isolation, the SB2000MK2 is a practical interface for the radio amateur who wants reliable cooperation between computer and transceiver.\u003c\/p\u003e\n\u003cp\u003eOrder the CGA SB2000MK2 and choose the appropriate interface cable for your Yaesu, Icom, or Kenwood transceiver.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOptional accessories (cable sets):\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003e\n\n\u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-interfacekabel-sb2000mk2-yaesu\" title=\"CGA ACC-101 interface cable to connect various Yaesu models to the CGA SB2000MK2 interface\"\u003eCGA ACC-101\u003c\/a\u003e: Yaesu FT-1000MP (MK-V, MK-V Field), FT-2000, FT-9000(DX)\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-102: Icom IC-746(Pro), IC-7400, IC-756(Pro, Pro2, Pro3)\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-sb2000mk2-interfacekabel-acc-103\" title=\"CGA ACC103 interface cable for the sb2000mk2 to connect your transceiver to a PC or laptop\"\u003eCGA ACC-103\u003c\/a\u003e: Icom IC-703, IC-706 (MK2, MK2G), IC-717, IC-78, IC-7000\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-acc-104-interfacekabel-yaesu-ft-450-ft-950\" title=\"CGA ACC-104 interface cable to connect your transceiver to the SB2000MK2 interface\"\u003eCGA ACC-104\u003c\/a\u003e: Yaesu FT-450, FT-950\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-105: Yaesu FT-100(D), FT-817, FT-857(D), FT-897(D)\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-sb2000-kabel-kenwood-13-pin\" title=\"CGA ACC-106 interface cable to connect various Kenwood transceivers to the CGA SB2000MK2 interface\"\u003eCGA ACC-106:\u003c\/a\u003e Kenwood TS-570, TS-2000\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-107: Kenwood TS-480 (SAT, HX)\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"CGA","offers":[{"title":"Default Title","offer_id":56101608063358,"sku":"CGA SB2000MK2","price":86.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/Achterkant_SB-2000-mk2-Interface.jpg?v=1755295466"},{"product_id":"cga-sb2000-kabel-kenwood-13-pin","title":"CGA SB2000 interface cable 13-pin Kenwood TK-570\/TS-2000\/TS-590","description":"\u003cp\u003eDo you want to reliably connect your Kenwood transceiver to the CGA SB2000MK2 interface? With this \u003cstrong\u003eCGA 13-Pin Kenwood interface cable\u003c\/strong\u003e, you can easily make the right connection between the SB2000MK2 and various Kenwood transceivers with a 13-pin connector. A practical solution for radio amateurs who want to connect their equipment neatly and reliably.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe right cable for your CGA SB2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-sb2000mk2-interface\" title=\"CGA SB2000MK2 interface module\"\u003eCGA SB2000MK2\u003c\/a\u003e is a compact interface that allows you to connect a computer and radio transceiver. This enables you to use digital modes and control various functions of your transceiver, such as RTTY, PSK31, SSTV, FAX, and CW.\u003c\/p\u003e\n\u003cp\u003eTo connect the interface to a suitable Kenwood transceiver, you naturally need the right cabling. This 13-pin data cable is specifically designed as an accessory for the CGA SB2000MK2 and provides the connection to compatible Kenwood transceivers.\u003c\/p\u003e\n\u003cp\u003eThe cable set includes a 13-pin data cable, a DB9 COM CAT cable for the RS232 protocol, and a 1\/8 inch connection for CW. This provides the connections needed to use the SB2000MK2 in combination with a suitable Kenwood transceiver.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich Kenwood transceivers is this cable suitable for?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAccording to the available product information, this CGA 13-Pin Kenwood interface cable is suitable for several popular Kenwood models, including the TS-570, TS-2000, TS-590, TS-990, and TS-870S.\u003c\/p\u003e\n\u003cp\u003eThis makes this cable interesting if you are already using a CGA SB2000MK2 and are looking for suitable cabling for your Kenwood. You don't have to search for various individual cables; instead, you can directly choose a cable set compiled for this application.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eSuitable as an interface cable for the CGA SB2000MK2\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003e13-pin data cable for compatible Kenwood transceivers\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eDB9 COM CAT cable with RS232 protocol\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003e1\/8 inch connection for CW\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eSuitable for Kenwood TS-570, TS-2000, TS-590, TS-990, and TS-870S\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eInterface cables for other transceivers also available\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAre you using a different radio? Other interface cables are also available for the CGA SB2000MK2 for various transceivers from Icom, Kenwood, and Yaesu, among others. This allows you to choose the cabling that suits your specific equipment.\u003c\/p\u003e\n\u003cp\u003eOrder the CGA 13-Pin Kenwood interface cable and reliably connect your compatible Kenwood transceiver to your CGA SB2000MK2.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe also have interface cables for other models for the SB2000MK2:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eCGA ACC-101: Yaesu FT-1000MP(MK-V, MK-V Field), FT-2000, FT-9000(DX).\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-102 for Icom with 8-pin ACC connector: Icom IC-746(Pro), IC-7400, IC-756xxx (Pro, Pro2, Pro3), IC-7600, IC-7700, IC-7800 and practically all recent Icom desktop transceivers. \u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-103 for Icom with 13-pin ACC connector: Icom IC-703, IC-706(MK2, MK2G, IC-717, IC-78) \u003cmeta charset=\"utf-8\"\u003eIC-718, IC-703, IC-706, IC-7000\u003cem\u003e, IC-7200, IC-7100\u003c\/em\u003e.\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-104: Yaesu FT-45, FT-950, \u003cmeta charset=\"utf-8\"\u003eYaesu FT-450 and FT-950 and FT-DX3000D (for Yaesu FT-847 see note*).\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-105: Yaesu FT-100(D), FT-817, FT-857(D), FT-897(D).\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-107: Kenwood TS-480SAT and TS-480HX.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e*Please note when using on VHF and UHF\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSome transceivers that support both HF and VHF, such as the Icom IC-746 and IC-7400, have separate PTT lines for HF (HSEND) and VHF (VSEND).\u003c\/p\u003e\n\u003cp\u003eThe CGA SB2000MK2 by default only controls the HSEND line. Without modification, the interface can therefore only be used for transmitting on HF with these transceivers.\u003c\/p\u003e\n\u003cp\u003eIf you want to use the CGA SB2000MK2 for VHF\/UHF as well, an adjustment to the transceiver or interface connector is necessary. Here, HSEND and VSEND must be controlled simultaneously by connecting both terminals together.\u003c\/p\u003e\n\u003cp\u003eWith transceivers such as the Icom IC-706Mk2G and IC-7000, this works differently. With these models, a setting can be adjusted via the menu so that HSEND also activates transmission on VHF and UHF.\u003c\/p\u003e\n\u003cp\u003eTherefore, always check the settings and connection options of your specific transceiver before use.\u003c\/p\u003e","brand":"CG Antenna","offers":[{"title":"Default Title","offer_id":57904466690430,"sku":"CGA ACC106","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/CGA-ACC-106-13-Pin-Kenwood-kabel.png?v=1787556620"},{"product_id":"cga-interfacekabel-sb2000mk2-yaesu","title":"CGA SB2000MK2 interface cable Yaesu FT-1000\/FT-2000\/FT-9000","description":"\u003cp\u003eThe \u003cstrong\u003eCGA ACC-101 interface cable\u003c\/strong\u003e connects a compatible Yaesu desktop transceiver to the \u003cstrong\u003eCGA SB-2000MK2 Soundcard \u0026amp; CAT Interface\u003c\/strong\u003e. The cable set is specifically designed for, among others, the Yaesu FT-1000MP series, FT-2000, and FT-9000DX and provides the necessary connections for data, CAT control, and CW.\u003c\/p\u003e\n\u003cp\u003eDo you use the \u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-sb2000mk2-interface\" title=\"CGA SB2000MK2 interface that can be placed between a computer or laptop and the transceiver\"\u003eCGA SB-2000MK2\u003c\/a\u003e to control your Yaesu transceiver from a computer or use digital modes? Then the ACC-101 offers the appropriate cabling to correctly connect both devices.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComplete cable set for the CGA SB-2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA ACC-101 combines various connections in one cable set. The set features a DIN-4 connector for RTTY data, a DIN-5 connector for Packet data, a DB9 COM connector for CAT control via RS232, and a 1\/4 inch connector for CW.\u003c\/p\u003e\n\u003cp\u003eThis makes the cable suitable for various functions supported by the SB-2000MK2. These include CAT control of the transceiver, PTT, FSK and CW-keying, and working with digital modes such as RTTY, PSK, SSTV, and FAX.\u003c\/p\u003e\n\u003cp\u003eThe SB-2000MK2 uses your computer's sound card. Good to know: the SB-2000MK2 itself does not contain a sound card. The interface connects to an existing sound card in the computer.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich Yaesu transceivers is the CGA ACC-101 suitable for?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAccording to the available product information, the CGA ACC-101 interface cable is intended for the following Yaesu transceivers:\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eYaesu FT-1000MP, including MK-V and MK-V Field\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eYaesu FT-2000\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eYaesu FT-9000DX\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eReliable connection for CAT and digital modes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA SB-2000MK2 features built-in conversion from RS232 to USB. This allows transceivers with an RS232 interface to be used via the SB-2000MK2 with a modern USB connection on the computer. For CAT control, a maximum speed of 19,200 baud is supported.\u003c\/p\u003e\n\u003cp\u003eThe Mk2 version also offers two virtual serial ports. This allows functions to be distributed: one virtual port can be used for PTT and CW\/FSK, while the other remains available for CAT control. This is practical for software that cannot process these functions via the same serial port.\u003c\/p\u003e\n\u003cp\u003eThe signals of the SB-2000MK2 are optically or transformer-isolated, and the interface is powered via the computer's USB connection.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e*Please note: this is the cable set\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA ACC-101 is a separately available interface cable for the CGA SB-2000MK2. The SB-2000MK2 interface itself is not described as part of this cable set.\u003c\/p\u003e\n\u003cp\u003eAlways check before ordering whether your exact Yaesu model matches the stated compatibility.\u003c\/p\u003e\n\u003cp\u003eConnect your Yaesu transceiver neatly to your CGA SB-2000MK2. Order the CGA ACC-101 interface cable and get the most out of your CAT control and digital modes.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe also have interface cables for the SB2000MK2 for other models:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eCGA ACC-101: Yaesu FT-1000MP(MK-V, MK-V Field), FT-2000, FT-9000(DX).\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-102 for Icom with 8 pin ACC connection: Icom IC-746(Pro), IC-7400, IC-756xxx (Pro, Pro2, Pro3), IC-7600, IC-7700, IC-7800 and practically all recent Icom desktop transceivers. \u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-103 for Icom with 13 pin ACC connection: Icom IC-703, IC-706(MK2, MK2G, IC-717, IC-78) IC-718, IC-703, IC-706, IC-7000\u003cem\u003e, IC-7200, IC-7100\u003c\/em\u003e.\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-104: Yaesu FT-45, FT-950,\u003cspan\u003e \u003c\/span\u003eYaesu FT-450 and FT-950 and FT-DX3000D (for the Yaesu FT-847 see remark*).\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-105: Yaesu FT-100(D), FT-817, FT-857(D), FT-897(D).\u003c\/li\u003e\n\n\u003cli\u003e\n\n\u003ca href=\"https:\/\/www.deltron.nl\/products\/cga-sb2000-kabel-kenwood-13-pin\" title=\"CGA ACC-106 Interface cable to connect Kenwood 13-pin to the CGA SB2000MK2\"\u003eCGA ACC-106:\u003c\/a\u003e For 13-Pin Kenwood TS-570, TS-2000, TS-590, TS-990 and TS-870S.\u003c\/li\u003e\n\n\u003cli\u003eCGA ACC-107: Kenwood TS-480SAT and TS-480HX.\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"CG Antenna","offers":[{"title":"Default Title","offer_id":57904491921790,"sku":"CGA ACC101","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/CGA-ACC-101-interfacekabel-yaesu.png?v=1787559646"},{"product_id":"cga-sb2000mk2-interfacekabel-acc-103","title":"CGA SB2000MK2 interface cable Icom","description":"\u003cp\u003eDo you want to connect your Icom transceiver to the CGA SB2000MK2 interface? The \u003cstrong\u003eCGA ACC-103 interface cable\u003c\/strong\u003e is designed for compatible Icom transceivers with a \u003cstrong\u003e13-pin ACC connector\u003c\/strong\u003e. This cable set provides the necessary connection between your transceiver and the SB2000MK2, allowing you to use the radio in conjunction with a computer or laptop.\u003c\/p\u003e\n\u003cp\u003eThe ACC-103 is suitable for various popular Icom transceivers, including the \u003cstrong\u003eIC-703, IC-706 series, IC-718, IC-78, IC-7000, IC-7200, and IC-7100\u003c\/strong\u003e, provided they have the appropriate 13-pin ACC connector.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe right 13-pin Icom cable for the CGA SB2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA SB2000MK2 acts as the interface between your computer and transceiver. It enables functions such as CAT\/CI-V control, digital modes, PTT, and CW, depending on the connected radio and the software used.\u003c\/p\u003e\n\u003cp\u003eTo correctly connect the SB2000MK2 to your Icom transceiver, you need a cable set that matches the radio's connectors. The CGA ACC-103 has been developed for compatible Icom models with a 13-pin ACC connector.\u003c\/p\u003e\n\u003cp\u003eThe cable set includes a 13-pin data cable, a 1\/8 inch CI-V cable, and a 1\/4 inch connector for CW. This conveniently bundles the necessary connections between the transceiver and SB2000MK2.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFor which Icom transceivers is the ACC-103 suitable?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA ACC-103 can be used for various Icom transceivers with a suitable 13-pin ACC connector. According to the available product information, these include the IC-703, IC-706, IC-706MK2, IC-706MK2G, IC-718, IC-78, IC-7000, IC-7200, and IC-7100.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eInterface cable for the CGA SB2000MK2\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eFor compatible Icom transceivers with 13-pin ACC connector\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eEquipped with a 13-pin data cable\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eIncludes 1\/8 inch CI-V cable and 1\/4 inch CW connector\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eFor IC-703, IC-706 series, IC-718, IC-78, IC-7000, IC-7200, and IC-7100, among others\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eConnect your Icom transceiver to your computer\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWith the combination of the CGA SB2000MK2 and ACC-103 interface cable, you can connect a suitable Icom transceiver to a computer or laptop. The SB2000MK2 acts as the interface between both devices, while the ACC-103 provides the model-specific connection to the Icom radio.\u003c\/p\u003e\n\u003cp\u003eThis makes this cable set interesting if you want to use digital modes, control the transceiver via suitable software, or control CW via the interface.\u003c\/p\u003e\n\u003cp\u003eBefore ordering, always check if your exact Icom model has the required connections. This ensures you choose the correct interface cable for your transceiver.\u003c\/p\u003e\n\u003cp\u003eOrder the CGA ACC-103 13-pin Icom interface cable and connect your compatible Icom transceiver to the CGA SB2000MK2.\u003c\/p\u003e","brand":"CG Antenna","offers":[{"title":"Default Title","offer_id":57904814424446,"sku":"CGA ACC103","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/CGA-ACC-103-interfacekabel-SB2000mk2-icom.png?v=1787828213"},{"product_id":"cga-acc-104-interfacekabel-yaesu-ft-450-ft-950","title":"CGA SB2000MK2 interface cable Yaesu FT-450\/FT-950","description":"\u003cp\u003eDo you want to connect your Yaesu transceiver to the CGA SB2000MK2 interface? The \u003cstrong\u003eCGA ACC-104 interface cable\u003c\/strong\u003e is designed for compatible Yaesu transceivers with a \u003cstrong\u003e6-pin Mini-DIN data connection and DB9 CAT connection.\u003c\/strong\u003e It creates the necessary connection between the SB2000MK2 and your transceiver for data communication and CAT control, among other things.\u003c\/p\u003e\n\u003cp\u003eThe ACC-104 is suitable for various popular Yaesu models, including the FT-450, FT-950, FTDX-3000, and FT-991.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe right Yaesu cable for the CGA SB2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFor a good connection between your transceiver and the CGA SB2000MK2, you need an interface cable that matches your radio's connections and communication. The CGA ACC-104 combines a 6-pin Mini-DIN data cable with a DB9 COM cable for CAT control via the RS232 protocol.\u003c\/p\u003e\n\u003cp\u003eIn addition, the cable set has a 1\/4 inch connector for CW. This means that with one cable set, you have the necessary connections for linking various compatible Yaesu transceivers to the SB2000MK2.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich Yaesu transceivers is the ACC-104 suitable for?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA ACC-104 can be used for various Yaesu transceivers. Based on the available product information, these include the Yaesu FT-450, FT-950, FTDX-3000, and FT-991.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eInterface cable for the CGA SB2000MK2\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eFor compatible Yaesu transceivers\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003e6-pin Mini-DIN data cable\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eDB9 COM CAT cable with RS232 protocol\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003e1\/4 inch connector for CW\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote when using with the Yaesu FT-847\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Yaesu FT-847 differs from the other mentioned Yaesu transceivers in terms of CAT connection. As a result, the CAT function with the ACC-104 does not work directly in the standard configuration.\u003c\/p\u003e\n\u003cp\u003eFor use with the FT-847, pins 2 and 3 of the DB9 connection must be crossed. This can be done, for example, with a suitable DB9 adapter where these two pins are reversed. The other mentioned Yaesu models use a straight DB9 connection according to the available information.\u003c\/p\u003e\n\u003cp\u003eDo you want to use the ACC-104 for an FT-847? Then keep in mind that modifying the DB9 connection is necessary for CAT communication. Always check the correct pin assignment of your equipment before connecting.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePractical cable set for your Yaesu interface\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWith the CGA ACC-104, you don't have to search for various separate data and CAT cables for a compatible Yaesu transceiver. The cable set is specifically designed to enable the connection with the CGA SB2000MK2 and provides connections for data, CAT, and CW.\u003c\/p\u003e\n\u003cp\u003eOrder the CGA ACC-104 interface cable and connect your compatible Yaesu transceiver to the CGA SB2000MK2.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"CG Antenna","offers":[{"title":"Default Title","offer_id":57904823730558,"sku":"CGA ACC104","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/CGA-ACC-104-Yaesu-DB9-FT450-FT950-interfacekabel.png?v=1787825561"},{"product_id":"cga-acc-103-interface-kabel-icom","title":"CGA SB2000MK2 13-pin Icom interface cable","description":"\u003cp\u003eDo you want to reliably connect your Icom transceiver to the CGA SB2000MK2 interface? With the \u003cstrong\u003eCGA ACC-103 13-pin Icom interface cable\u003c\/strong\u003e, you make the correct connection between the SB2000MK2 and various compatible Icom transceivers with a 13-pin connector. A practical solution for radio amateurs who want to connect their transceiver and computer via the CGA interface.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe right Icom cable for your CGA SB2000MK2\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe CGA SB2000MK2 is an interface that allows you to connect a computer and radio transceiver. This enables you to use various digital modes and control functions of the connected transceiver.\u003c\/p\u003e\n\u003cp\u003eFor this, it is important to use an interface cable that matches your transceiver's connector. The CGA ACC-103 is specifically designed for compatible Icom transceivers with a 13-pin connector and forms the connection between the radio and the CGA SB2000MK2.\u003c\/p\u003e\n\u003cp\u003eThe cable set consists of a 13-pin data cable, a 1\/8 inch CI-V cable, and a 1\/4 inch connector for CW. This provides you with the necessary connections to link a suitable Icom transceiver to the SB2000MK2.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFor which Icom transceivers is the CGA ACC-103 suitable?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAccording to the available product information, the CGA ACC-103 is suitable for various well-known Icom transceivers with a 13-pin connector. These include the Icom IC-703, IC-706, IC-706MK2, IC-706MK2G, IC-718, IC-78, IC-7000, and IC-7200.\u003c\/p\u003e\n\u003cp\u003eDo you own one of these models and use the CGA SB2000MK2? Then you don't have to search for various loose cables and connectors yourself. With the ACC-103, you directly choose the Icom cable set that has been assembled for this application.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eInterface cable for the CGA SB2000MK2\u003c\/li\u003e\n\n\u003cli\u003eDesigned for compatible Icom transceivers with 13-pin connector\u003c\/li\u003e\n\n\u003cli\u003eEquipped with a 13-pin data cable\u003c\/li\u003e\n\n\u003cli\u003eIncludes 1\/8 inch CI-V cable and 1\/4 inch CW connector\u003c\/li\u003e\n\n\u003cli\u003eSuitable for Icom IC-703, IC-706 series \u003cmeta charset=\"utf-8\"\u003e(MK2, MK2G), IC-718, IC-78, IC-7000, and IC-7200, among others.\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eAlso interface cables for other transceivers\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDo you use a different transceiver? Various interface cables are available for the CGA SB2000MK2 for radios from Icom, Kenwood, and Yaesu, among others. Always check the transceiver type and the required connection to choose the correct cable for your equipment.\u003c\/p\u003e\n\u003cp\u003eOrder the CGA ACC-103 13-pin Icom interface cable and reliably connect your compatible Icom transceiver to the CGA SB2000MK2.\u003c\/p\u003e","brand":"CG Antenna","offers":[{"title":"Default Title","offer_id":57910695068030,"sku":"CGA ACC103","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/CGA-ACC103-interfacekabel-13p-icom.png?v=1787825189"},{"product_id":"midland-interface-met-pcb-8001-pro","title":"Midland interface with PCB for 8001 Pro","description":"\u003cp\u003eDo you want to connect a Midland 8001 Pro for communication with suitable programming software? This \u003cstrong\u003eMidland interface with cable and PCB\u003c\/strong\u003e is specifically intended for use with the \u003cstrong\u003eMidland 8001 Pro 27 MHz SSB transceiver\u003c\/strong\u003e. The interface provides the connection between the transceiver and the programming environment and is supplied as a cable with an integrated PCB.\u003c\/p\u003e\n\u003cp\u003eBy choosing a model-specific interface for the Midland 8001 Pro, you have a solution that is tailored to this transceiver. Ideal if you want to use the Midland 8001 Pro in combination with suitable programming software.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInterface specifically for the Midland 8001 Pro\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis interface was developed for the Midland 8001 Pro 27 MHz SSB transceiver. The cable is equipped with a PCB and the necessary connection for connecting to the radio.\u003c\/p\u003e\n\u003cp\u003eA good physical connection between the interface and transceiver is important. According to the included instructions, the RJ connector must be fully inserted into the radio's connection to enable optimal communication between the radio and programming software.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe most important features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\n\u003cli\u003eInterface with cable and PCB\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eSpecifically for the Midland 8001 Pro\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eFor use with the 27 MHz SSB transceiver\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eIntended for communication with suitable programming software\u003cbr\u003e\n\n\u003c\/li\u003e\n\n\u003cli\u003eModel-specific solution for the Midland 8001 Pro\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003ePay attention when connecting the RJ connector\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBefore programming, check that the RJ connector is fully inserted into the transceiver. A connector that does not make full contact can disrupt communication between the radio and software.\u003c\/p\u003e\n\u003cp\u003eIf it turns out during programming that the connection is not established properly, the manufacturer advises applying light pressure to the connector. This ensures that the male and female RJ connectors connect correctly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eATTENTION!: \u003c\/strong\u003eAlways check the connection carefully before looking for another cause of communication problems.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eConnecting Midland 8001 Pro to programming software\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis Midland interface for the 8001 Pro is a practical choice when you want to connect the transceiver for use with compatible programming software. Because the interface is specifically designed for this model, you do not have to assemble a generic cable solution yourself.\u003c\/p\u003e\n\u003cp\u003eDo you use a Midland 8001 Pro and are you looking for the right interface cable with PCB? Then this interface offers a model-specific solution for your 27 MHz SSB transceiver.\u003c\/p\u003e\n\u003cp\u003eOrder the Midland interface with cable and PCB for the 8001 Pro and use your transceiver with suitable programming software.\u003c\/p\u003e","brand":"Midland","offers":[{"title":"Default Title","offer_id":57922837709182,"sku":"MIDL 102262","price":159.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0651\/3052\/8953\/files\/Midland-8001-pro-interface-set.png?v=1787830096"}],"url":"https:\/\/www.deltron.nl\/en\/collections\/interfaces.oembed","provider":"Deltron","version":"1.0","type":"link"}